Fox Rp23 Service Manual
You are here: FLOAT FLOAT RP23 FLOAT RP23 REAR SHOCK features/adjustments high volume standard air sleeve, boost valve, angled air valve, lightweight chassis, DOHC ProPedal with 2 positions, ProPedal tuning adjust with 3 positions, air spring pressure, rebound adjust spring air intended use freeride, all-mountain, cross-country Installing Your Shock If you are installing your shock on a bike in which the shock is not original equipment:. Install the shock. Remove the main air chamber air cap and let all the air out of the main air chamber.
Shock Absorber Rebuild Manual Models FLOAT. Recommended Service Intervals Recommended Service Intervals Your FOX Racing Shox will perform the best if serviced. Fox Rp23 Service Manual Wwwridefoxcom, wij willen hier een beschrijving geven, maar de site die u nu bekijkt staat dit niet toe. Air sleeve maintenance fox racing. Aug 24, 2013 How to service air chamber on Fox Float RP23. All you need is original service/seals kit. Don't forget to subscribe, rate and comment. More at http.
Carefully cycle the suspension through its entire travel. Check that all parts of the shock are clear of the frame and swingarm as it cycles through the travel. Pressurize your main air chamber to a minimum of 50 psi and no more than 300 psi. You will tune to a more specific air pressure in the section below. General Maintenance There may be a small amount of air sleeve lubricant residue on the body.
This is normal. If this residual air sleeve lubricant is not present, this is an indication that the air sleeve should be re-lubricated.
Some other things to consider for all shock models:. If you ride in extreme conditions, service your shock and air sleeve more frequently. For your shock. Wash your shock with soap and water only.
Do not use a high pressure washer to clean your shock. Internal service should be performed by FOX Racing Shox or an.
Fox Rp23 Service Manual
Before You Ride. Torrent subliminal visualizer pro. Clean the outside of your shock with soap and water and wipe dry with a soft dry rag.
Do not use a on your shock. Inspect entire exterior of shock for damage.
The shock should not be used if any of the exterior parts appear to be damaged. Please or FOX Racing Shox for further inspection and repair.
Fox Float Rp23 Settings
Check that quick-release levers (or thru-axle pinch bolts) are properly adjusted and tightened. Check headset adjustment. If loose, adjust according to manufacturer’s recommendations. Check that brake cables or hoses are properly fastened. Check that the front and rear brakes operate properly on flat land. Setting Sag You can also view a.
To set sag:., and compare it to the recommended sag setting shown in the table below. Continue if the sag is not to specification. Locate the Schrader air valve on the shock and remove the air valve cap.
Screw the onto the air valve until the pump shows pressure on the gauge. Do not over-tighten. Add air pressure until desired pressure is shown on the gauge. Refer to the table below for the proper sag setting. Unthread the pump from the air valve and measure sag. Repeat steps 2-5 until proper sag is achieved, then replace the air valve cap. Air Spring Setting Guidelines Shock Travel (in./mm) Sag (in./mm) 1.00/25.4 0.25/6.4 1.25/31.7 0.31/7.9 1.50/38.1 0.38/9.5 1.75/44.4 0.44/11.1 2.00/50.8 0.50/12.7 2.25/57.1 0.56/14.2 Adjusting Rebound Rebound controls the rate at which your shock returns after it has been compressed.
The proper rebound setting is a personal preference, and changes with rider weight, riding style and conditions. A rule of thumb is that rebound should be as fast as possible without kicking back and pushing the rider off the saddle. The rebound knob has 8-10 clicks of adjustment.
For slower rebound, turn the red adjuster knob clockwise. For faster rebound, turn the red adjuster knob counterclockwise. ProPedal ProPedal Lever The ProPedal lever allows for on-the-fly ProPedal adjustment. ProPedal damping reduces pedal-induced suspension bob. The two ProPedal lever settings are:.
OPEN. PROPEDAL Use each setting to adjust the shock for different riding conditions and situations. For example, use PROPEDAL for riding to the top of the mountain, and then switch to OPEN for the descent. To determine which ProPedal position is better for your condition and situation, pedal the bicycle and monitor the shock movement.
Switch between positions and select the one that reduces suspension movement most effectively while providing the desired amount of bump absorption. Because suspension designs and riding skills vary, optimal settings can vary from bike to bike and rider to rider.
For more precise ProPedal tuning and to further eliminate pedal-induced bob while maintaining bump compliance, adjust the ProPedal knob. As with the ProPedal lever, switch positions and select a setting that reduces suspension movement most effectively while providing the desired amount of bump absorption. ProPedal Knob The 3-position ProPedal knob (shown below) allows you to adjust ProPedal firmness when the ProPedal lever is in the PROPEDAL position. The ProPedal knob only changes damping when the ProPedal lever is in the PROPEDAL position. The ProPedal knob settings are denoted by the numbers etched onto the ProPedal knob. The three ProPedal knob settings are:. (1) PROPEDAL Light.
(2) PROPEDAL Medium. (3) PROPEDAL Firm To adjust the ProPedal knob:. Turn the ProPedal lever to the PROPEDAL position, as shown in graphic above. Lift the ProPedal knob (see frame #2 in the drawing below).
Turn the ProPedal knob clockwise (relative to the ProPedal knob facing the user) until the selection you want—1, 2, or 3—is aligned with the ProPedal lever ( #3). The ProPedal knob clicks twice per setting as it turns. The first click occurs as you exit the current setting; the second click as you engage the new setting. Push the ProPedal knob into its new position ( #4). Caution!The ProPedal knob should NOT be adjusted on-the-fly. It should only be adjusted while in a stationary position. Turning the ProPedal knob (animated clip): Copyright © 2009 FOX Factory Inc.